You're viewing a previously published revision of this guide.  View latest revision

Older
Mar 26, 2014 - 03:03:54
Apr 02, 2014 - 07:04:48 Apr 02, 2014 - 07:04:16 Apr 02, 2014 - 07:04:06 Mar 31, 2014 - 06:03:34 Mar 31, 2014 - 06:03:47 Mar 31, 2014 - 06:03:08 Mar 31, 2014 - 06:03:32 Mar 31, 2014 - 06:03:14 Mar 31, 2014 - 06:03:06 Mar 31, 2014 - 09:03:38 Mar 31, 2014 - 09:03:54 Mar 31, 2014 - 09:03:07 Mar 31, 2014 - 09:03:50 Mar 31, 2014 - 09:03:50 Mar 31, 2014 - 08:03:10 Mar 26, 2014 - 03:03:26 Mar 26, 2014 - 03:03:50 Mar 26, 2014 - 03:03:45 Mar 26, 2014 - 03:03:54 Mar 26, 2014 - 03:03:49 Mar 26, 2014 - 03:03:25 Mar 26, 2014 - 03:03:30 Mar 26, 2014 - 03:03:40 Mar 26, 2014 - 03:03:23 Mar 26, 2014 - 03:03:07 Mar 26, 2014 - 03:03:07 Mar 26, 2014 - 03:03:27 Mar 26, 2014 - 03:03:27 Mar 26, 2014 - 03:03:49 Mar 26, 2014 - 03:03:49 Mar 26, 2014 - 03:03:36 Mar 26, 2014 - 03:03:18 Mar 26, 2014 - 03:03:17 Mar 26, 2014 - 03:03:42 Mar 26, 2014 - 03:03:18 Mar 26, 2014 - 03:03:50 Mar 26, 2014 - 03:03:34
Newer

Installing Soil Mixer - Module - Toothbar Teeth

Written By: Andrew Graham (and 2 other contributors)
  • Comments: 0
  • Favorites: 0
  • Completions: 1

Difficulty

Moderate

Steps

5

Time Required

Suggest a time??

Sections

1

Flags

2

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

User-Contributed Guide

User-Contributed Guide

This guide is not managed by the site's staff.

Quiz

0

  1. Take P18 Lay P19 flat

    • Take P18

    • Lay P19 flat

    • Weld P18 with 1" overlap onto center of P19

  2. Weld P20 to make 1/2" of P19 (cutting knife) exposed at the cutting edge Repeat for the total 12 teeth

    • Weld P20 to make 1/2" of P19 (cutting knife) exposed at the cutting edge

    • Repeat for the total 12 teeth

  3. Weld 4 teeth at the proper spacing (4" on center ? and 2" on center from edge ? ) to part 15 (tooth bar bolt bar), with X inches overlap between 18 and 15 Repeat for the 2 other parts 15

    • Weld 4 teeth at the proper spacing (4" on center ? and 2" on center from edge ? ) to part 15 (tooth bar bolt bar), with X inches overlap between 18 and 15

    • Repeat for the 2 other parts 15

  4. Grind teeth at 45 degree angle with tooth bar weldment in a vice

    • Grind teeth at 45 degree angle with tooth bar weldment in a vice

    • Water harden or air harden the teeth by heating to red hot with acetylene torch and then dunking in water

    • Quality control Checklist

    • Make sure that 18 and 19 overlap by 1"

    • Make sure that 18 and 19 are centered with respect to one another

    • Make sure that 1/2" of cutting knife is exposed, and that 1/4" is exposed after grinding

    • Make sure that 15 is oriented with the holes pointing away from the teeth

    • Make sure that the angle between 15 and 18 is 90 degrees

Author

with 2 other contributors

Andrew Graham

Member since: 2/15/14

197 Reputation

5 Guides authored

View Statistics:

Past 24 Hours: 0

Past 7 Days: 1

Past 30 Days: 11

All Time: 261