You're viewing a previously published revision of this guide.  View latest revision

Older
Mar 27, 2014 - 10:03:51
Apr 04, 2014 - 10:04:48 Apr 04, 2014 - 10:04:40 Apr 04, 2014 - 10:04:23 Apr 04, 2014 - 10:04:48 Apr 04, 2014 - 09:04:05 Apr 04, 2014 - 09:04:36 Apr 04, 2014 - 09:04:20 Apr 04, 2014 - 09:04:40 Apr 04, 2014 - 09:04:21 Apr 04, 2014 - 09:04:16 Apr 04, 2014 - 09:04:51 Apr 04, 2014 - 07:04:16 Apr 01, 2014 - 01:04:59 Mar 31, 2014 - 08:03:57 Mar 31, 2014 - 08:03:07 Mar 31, 2014 - 08:03:16 Mar 31, 2014 - 08:03:09 Mar 31, 2014 - 08:03:09 Mar 31, 2014 - 08:03:55 Mar 31, 2014 - 08:03:11 Mar 31, 2014 - 08:03:17 Mar 31, 2014 - 07:03:00 Mar 31, 2014 - 07:03:11 Mar 31, 2014 - 07:03:10 Mar 31, 2014 - 07:03:21 Mar 31, 2014 - 07:03:20 Mar 27, 2014 - 12:03:01 Mar 27, 2014 - 11:03:03 Mar 27, 2014 - 11:03:03 Mar 27, 2014 - 11:03:39 Mar 27, 2014 - 11:03:39 Mar 27, 2014 - 10:03:51 Mar 27, 2014 - 10:03:19 Mar 27, 2014 - 10:03:52 Mar 27, 2014 - 10:03:52 Mar 27, 2014 - 10:03:30 Mar 27, 2014 - 10:03:30 Mar 27, 2014 - 08:03:59 Mar 27, 2014 - 08:03:19 Mar 26, 2014 - 03:03:57 Mar 26, 2014 - 12:03:14 Mar 26, 2014 - 12:03:40 Mar 26, 2014 - 12:03:21 Mar 26, 2014 - 12:03:48 Mar 26, 2014 - 12:03:48 Mar 26, 2014 - 12:03:26 Mar 26, 2014 - 12:03:42 Mar 26, 2014 - 12:03:28 Mar 13, 2014 - 09:03:32 Mar 13, 2014 - 08:03:36
Newer

Installing Soil Mixer - Module - Bucket

Written By: Anthony Douglas (and 2 other contributors)
  • Comments: 0
  • Favorites: 0
  • Completions: 3

Difficulty

Moderate

Steps

3

Time Required

Suggest a time??

Sections

1

Flags

2

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

User-Contributed Guide

User-Contributed Guide

This guide is not managed by the site's staff.

Quiz

0

  1. Take P3 (Part 3) Bottom Sheet for bucket and lay flat. Tack weld backplate (P1) using a set square at a 90 degree angle on top of P3, don't finish the weld until the sidewalls have also been tacked.

    • Take P3 (Part 3) Bottom Sheet for bucket and lay flat.

    • Tack weld backplate (P1) using a set square at a 90 degree angle on top of P3, don't finish the weld until the sidewalls have also been tacked.

  2. Mount bearings with 1" bolts loosely on the side plates P5 and P4 with bearing mount plate P23.

    • Mount bearings with 1" bolts loosely on the side plates P5 and P4 with bearing mount plate P23.

  3. Tack weld backplate (P1) using a set square at a 90 degree angle on top of P3, don't finish the weld. tack sidewall P4 into place at 90 degrees. Hold sidewall (P5) into place, and then stick Shaft 21 through the bearings to ensure proper alignment of side walls. Tack sidewall (P4). Now tighten the bolts, ensuring the shaft is aligned correctly.

    • Tack weld backplate (P1) using a set square at a 90 degree angle on top of P3, don't finish the weld. tack sidewall P4 into place at 90 degrees.

    • Hold sidewall (P5) into place, and then stick Shaft 21 through the bearings to ensure proper alignment of side walls. Tack sidewall (P4). Now tighten the bolts, ensuring the shaft is aligned correctly.

    • Finish welding the seams for the back plate, bottom sheet and sidewalls (P1, P3, P4, P5). Weld in the 1" nuts on the inside side of the sidewalls

Author

with 2 other contributors

Anthony Douglas

Member since: 3/12/14

101 Reputation

4 Guides authored

View Statistics:

Past 24 Hours: 0

Past 7 Days: 1

Past 30 Days: 2

All Time: 198