You're viewing a previously published revision of this guide. View latest revision

Jul 12, 2013 - 02:07:29

Oct 20, 2013 - 06:10:55 Oct 20, 2013 - 05:10:06 Oct 20, 2013 - 05:10:15 Oct 20, 2013 - 05:10:19 Oct 20, 2013 - 05:10:19 Oct 20, 2013 - 05:10:34 Oct 20, 2013 - 04:10:24 Oct 20, 2013 - 04:10:16 Oct 20, 2013 - 04:10:02 Oct 15, 2013 - 01:10:28 Jul 19, 2013 - 05:07:22 Jul 12, 2013 - 07:07:16 Jul 12, 2013 - 07:07:09 Jul 12, 2013 - 07:07:56 Jul 12, 2013 - 07:07:45 Jul 12, 2013 - 07:07:13 Jul 12, 2013 - 07:07:57 Jul 12, 2013 - 07:07:03 Jul 12, 2013 - 06:07:39 Jul 12, 2013 - 06:07:22 Jul 12, 2013 - 06:07:15 Jul 12, 2013 - 06:07:12 Jul 12, 2013 - 06:07:00 Jul 12, 2013 - 06:07:07 Jul 12, 2013 - 06:07:34 Jul 12, 2013 - 06:07:10 Jul 12, 2013 - 06:07:14 Jul 12, 2013 - 06:07:36 Jul 12, 2013 - 06:07:52 Jul 12, 2013 - 06:07:47 Jul 12, 2013 - 06:07:26 Jul 12, 2013 - 05:07:36 Jul 12, 2013 - 05:07:54 Jul 12, 2013 - 05:07:00 Jul 12, 2013 - 05:07:21 Jul 12, 2013 - 05:07:41 Jul 12, 2013 - 04:07:12 Jul 12, 2013 - 04:07:51 Jul 12, 2013 - 04:07:04 Jul 12, 2013 - 04:07:22 Jul 12, 2013 - 04:07:55 Jul 12, 2013 - 04:07:56 Jul 12, 2013 - 04:07:57 Jul 12, 2013 - 04:07:55 Jul 12, 2013 - 04:07:52 Jul 12, 2013 - 04:07:28 Jul 12, 2013 - 04:07:46 Jul 12, 2013 - 02:07:01 Jul 12, 2013 - 02:07:01 Jul 12, 2013 - 02:07:29 Jul 12, 2013 - 02:07:05 Jul 12, 2013 - 02:07:43 Jul 12, 2013 - 02:07:31 Jul 12, 2013 - 02:07:22

Newer

How to Construct the Bucket

Written By: Brian Peters (and 2 other contributors)

Comments: 1
Favorites: 0
Completions: 1

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Step 1 How to Construct the Bucket

All plates are ½” thick steel. Start with two plates cut according to the dimensions in the Fig. The large piece in the center is called “Bucket Side Plate”. Two are required to complete the Bucket. The two smaller triangles at the bottom were designed to be 30/60/90 triangles. The 30/60/90 triangles should control/drive the linear dimensions.

All plates are ½” thick steel. Start with two plates cut according to the dimensions in the Fig. The large piece in the center is called “Bucket Side Plate”. Two are required to complete the Bucket. The two smaller triangles at the bottom were designed to be 30/60/90 triangles. The 30/60/90 triangles should control/drive the linear dimensions.
New line.

Step 2

Cut a single 8"x16" plate according to the dimensions in the Fig. below. Note: that the holes are centered horizontally but are not centered vertically.

Cut a single 8"x16" plate according to the dimensions in the Fig. below. Note: that the holes are centered horizontally but are not centered vertically.